Summary of the content on the page No. 1
PORTABLE
COMPACT DISC PLAYER
WITH ANTI-SHOCK 10SEC.
INSTRUCTION MANUAL
PLEASE READ CAREFULLY BEFORE USING YOUR UNIT
MODEL: JX-CD476
Summary of the content on the page No. 2
LOCATION OF CONTROLS SKIP/SEARCH BACKWARD SKIP/SEARCH FORWARD ANTI-SKIP (ASP) (NOT INCLUDED) RECHARGE INDICATOR CONTROL OPERATION AND FUNCTION POWER SUPPLY Your CD player requires 2 size “AA” alkaline batteries (not included), or use the AC adaptor 4.5V 600mA (not included) AC ADAPTOR OPERATION Plug one end of the AC adaptor into the DC 4.5V jack, then plug the other end into AC wall outlet. (not included) PRECAUTIONS ON USING THE AC ADAPTOR Put in AC adaptor spec. Please make sure you purchase
Summary of the content on the page No. 3
BATTERIES MAY EXPLODE OR LEAK. 2. Plug in the AC adaptor. (not included) 3. Slide the charge switch to ON position to start charging. The charge indicator will light up. USE ONLY THE AC ADAPTOR FOR CHARGING. 4. After 15 hours, please unplug the AC adaptor and slide the recharge switch to OFF position. DO NOT CHARGE CONTINUOUSLY FOR 24 HOURS OR MORE. DOING SO CAN CAUSE THE PERFORMANCE OF THE RE- CHARGEABLE BATTERIES TO DETERIORATE. CHARGE SWITCH NOTE: You may play DISC’S whilst charging the batte
Summary of the content on the page No. 4
1.HOLD KEY 2. Stop button: Press this button when you finish to play. 2.STOP 4.CD SKIP 3. Play/Pause: Press this button, then the disc will begin to start. To stop play temporarily, press this button again. 5.PHONE JACK 4. CD Skip: Press these buttons during play to skip to the desired track. Press these buttons and hold during play to scan the disc at high speed. 3.PLAY/PAUSE 5. Phone Jack: Plug headphone in this jack to listen mu- sic. 6.VOLUME CONTROL 6. Volume Control: Adjust this volume
Summary of the content on the page No. 5
During programming, “PROG” flashes in the display. NOTE: Programming is possible in the STOP mode. Program number 12 3 Track number 35 9 1. Press the PROGRAM button in the STOP MODE. The “PROG” appears in the display. 2. Press the skip button ( ) to select the first track to be programmed. 3. Press the PROGRAM button again to enter the track into the memory. 4. Repeat steps 2 to 3 to program other track till you finish. 5. After programming is finished, press the PLAY/PAUSE Button. “PROG” shows
Summary of the content on the page No. 6
THE HOLD FUNCTION It is useful during playing, the function will lock the key on the panel to protect the mistake during playing. During playing slide the HOLD switch to ‘ON’ position, the ‘HOLD’ will appear in the display, the key on the panel will be locked, the panel keys are disabled. Slide the HOLD switch to ‘OFF’ position to stop the function. THE ANTI-SKIP MEMORY FUNCTION (10SEC.) The digital anti-skip function uses semiconductor memory to prevent the sound from skipping when the unit is
Summary of the content on the page No. 7
• FINGERPRINTS ON LENS Use a cotton swab starting in the middle and working to the outside edge, pay attention in doing this operation or the pick up lens could be damaged. CLEANING THE CABINET Wipe with a soft cloth. If the cabinet is very dirty, dampen (not dripping wet) the cloth with a weak solution of soap water, and then wipe clean. HANDLING COMPACT DISCS COMPACT 1. This unit is designed to play compact discs bearing the identification logo to the right. Discs that do not carry this logo m
Summary of the content on the page No. 8
TROUBLE SHOOTING GUIDE SYMPTOM CAUSE SOLUTION Dead or weak batteries. Replace both batteries. CD Player will not The AC adaptor not Check the AC adaptor connection at AC turn on. connected properly. outlet and side of set. Disc inserted incorrectly Re-insert disc with label side facing up. Defective or wrong type Try another audio compact disc. compact disc. Close lid securely (push down left corner Disc will not play. CD door not closed. of door) Take out the CD and leave the CD door Moisture h
