Summary of the content on the page No. 1
[ Quick Start Guide ]
I N T ELL IGENT S T ORA G E ROUTER INS T A LLA TI ON
z
iSR6200
QUICK START GUIDE
Summary of the content on the page No. 2
Purchasers of OEM products should consult with the OEM for support. Please feel free to contact your QLogic approved reseller or QLogic Technical Support at any phase of integration for assistance. QLogic Technical Support can be reached by the following methods: Web http://support.qlogic.com E-mail support@qlogic.com The QLogic knowledge database contains troubleshooting information for the QLogic adapters. Access the database from the QLogic Support Web page, http://support.qlogic.com. Use
Summary of the content on the page No. 3
Quick Start Guide ® The QLogic iSR6200 Series of intelligent Storage Router (iSR) provides servers with iSCSI connectivity to SAN-attached Fibre Channel based disk or tape storage. Suggested Configurations Figure 1 shows the iSR6200 connecting iSCSI servers to a direct-attached storage array. Fibre Channel iSCSI iSCSI iSCSI iSR6200 Initiator IP Switched Network RAID-Based Fibre Server Channel Storage System Figure 1. iSR6200 in Direct Attach Configuration Figure 2 shows the iSR6200 connectin
Summary of the content on the page No. 4
Installation Instructions This quick start guide provides procedures for installing and configuring your new QLogic iSR6200 router. ■ Step 1. Verify the package contents. ■ Step 2. Complete the pre-installation checklist. ■ Step 3. Mount the router. ■ Step 4. As needed, insert additional blade into router. ■ Step 5. Install the small form factor pluggable (SFP) transceivers. ■ Step 6. Apply power to the router. ® ■ Step 7. Download and install SANsurfer Router Manager ■ Step 8. Configure the iSR
Summary of the content on the page No. 5
Step 2. Complete the Pre-Installation Checklist During the initial configuration process, the system prompts you to enter information for each blade contained in the iSR6200. Use the spaces provided in Table 1 and Table 2 to record the IP addresses for each blade. Table 1. Worksheet for Router Blade 1 (left) Parameters Symbolic name of the iSR6200 Blade 1 Management port IP address, subnet mask, and gateway (if not using DHCP) iSCSI port 1 IP address, subnet mask, and gateway (GE-1) IP addre
Summary of the content on the page No. 6
Table 2. Worksheet for Router Blade 2 (right) Parameters (Continued) iSCSI port 3 IP address, subnet mask, and gateway for the optional (FC3, GE-3, or 10GE-3) port IP address of the iSNS server for iSCSI port 3 (if iSNS will be enabled) iSCSI port 4 IP address, subnet mask, and gateway for the optional (FC4, GE-4, or 10GE-4) port IP address of the iSNS server for iSCSI port 4 (if iSNS will be enabled) Step 3. Mount the Router To mount the iSR6200 router in the rack, follow the instruction
Summary of the content on the page No. 7
10GbE2 10GbE1 iSR6250 Intelligent Storage Router 10GbE2 10GbE1 iSR6250 Intelligent Storage Router 10GbE2 10GbE1 iSR6250 Intelligent Storage Router Step 6. Apply Power to the Router The iSR6200 router chassis contains one or two router blades, along with a power cooling module (PCM) for each blade. Each chassis blade provides light emitting diodes (LEDs) and connectors that face the front of the chassis. Each PCM provides a power connector, as well as an LED (see Figure 3). Front Plate iSR6200
Summary of the content on the page No. 8
The iSR6240 router blade (see Figure 5) adds two iSCSI Ethernet ports to the blade configuration. Each port has the following capacity: ❑ Auto negotiating transmission rates of 100 and 1000Mbps ❑ Full duplex transmission mode ❑ Support for jumbo frames (at 1000Mbps only) ❑ RJ45 copper Ethernet connector type ❑ iSCSI header and data digest in the hardware ❑ IPv4 and IPv6 protocol support ❑ iSCSI offload Activity Link Status Figure 5. iSCSI (GE) Ports on the iSR6240 Router Blade The iSR6250 rou
Summary of the content on the page No. 9
Step 7. Download and Install SANsurfer Router Manager Follow these steps to download the SANsurfer Router Manager tool from the QLogic Web site and install it on a workstation: 1. Close all programs currently running. 2. Go to the QLogic Downloads and Documentation page located here: http://driverdownloads.qlogic.com/ 3. Under QLogic Products, type iSR6200 in the search box. (Alternatively, you can click the Guided Search link to obtain assistance in locating the utility to download.) 4. In
Summary of the content on the page No. 10
WARNING: The following command might cause a loss of connections to the MGMT port. IPv4 Interface (0=Enable, 1=Disable) [Enabled ] IPv4 Mode (0=Static, 1=DHCP, 2=Bootp, 3=Rarp) [Dhcp ] 0 IPv4 Address [10.0.0.1 ] 172.17.136.55 IPv4 Subnet Mask [255.0.0.0 ] 255.255.254.0 IPv4 Gateway [0.0.0.0 ] 172.17.136.1 IPv6 Int
Summary of the content on the page No. 11
3. Create the iSCSI initiator list in iSR6200 using one of the following methods: ❑ Method 1: Enter the iSCSI initiator name using the SANsurfer Router Manager’s Add Initiator Wizard. The system prompts you to enter the iSCSI name of an initiator. ❑ Method 2: From the server with iSCSI initiators, run a discovery session for the iSCSI port IP address of the iSR6200. This automatically registers the iSCSI initiator names with the iSR6200. Running the iSCSI discovery session on different OS env
Summary of the content on the page No. 12
The iSCSI initiator name appears under the Discovered iSCSI Initiators node in the router tree in the left pane, and details for the initiator appear on the Information page in the right pane (see Figure 9). Figure 9. Discovered iSCSI Initiators Information To assign a LUN to a server, run the Target Presentation/LUN Mapping Wizard. This wizard allows you to map a LUN to the iSCSI initiator on your server. b. On the Wizards menu, click LUN Presentation Wizard. c. On the LUN Presentation Typ
Summary of the content on the page No. 13
d. On the Select the Initiators for LUN Presentation window (Figure 10), select one or more initiators, and then click Next. Figure 10. Target Presentation/LUN Mapping Wizard: Selecting Initiators e. On the LUN Selection window, select one or more LUNs under the virtual port group node, and then click Next. f. On the Confirm Changes window, review the LUN presentation information, and then click Next. g. In the Security Check dialog box, type the admin password, and then click OK to continue
Summary of the content on the page No. 14
h. On the LUN Masking Configuration Status window (Figure 11), review the results of the target ports presented for the selected initiators, and then click Finish. Figure 11. Target Presentation/LUN Mapping Wizard: Viewing Status 5. Log into the iSCSI initiator. For example, if you are using the Microsoft iSCSI initiator, follow these steps: a. On the iSCSI Initiator Properties dialog box, click the Targets tab. b. On the Targets page, select the target (the status is Inactive), and then click
Summary of the content on the page No. 15
After the iSCSI initiator logs into the newly presented LUN, the iSCSI Initiator Properties Targets page (see Figure 12) shows the target status as Connected. Figure 12. iSCSI Initiator Properties: Target Connected Now, when you select your iSCSI initiator in the left pane of the SANsurfer Router Manager window, the Information page shows the status as Logged In. The LUN List page (Figure 13) shows the LUNs mapped to that initiator. Figure 13. LUN List Page Step 10. Configure Second Blade (i
Summary of the content on the page No. 16
Step 11. Configure an FCIP Route Fibre Channel over IP (FCIP)—a licensed feature of the iSR6200—is a protocol used to transport Fibre Channel frames over TCP/IP to provide SAN-over-WAN capabilities. FCIP is commonly used to interconnect (merge) SANs that are separated by such a distance that a direct connection is cost-prohibitive or technically unfeasible. For detailed information about configuring FCIP parameters, refer to the iSR6200 QLogic intelligent Storage Router (iSR) Installation Gui
Summary of the content on the page No. 17
Using the CLI to Locate the Serial Number To find the serial number of your blade from the command line, follow these steps: 1. Telnet into the iSR6200, and then start the CLI. 2. Log in as guest; the default password is password. 3. Issue the show chassis command. 4. Under Blade x Information, locate and write down the serial number for each blade. In the following example, the two blade serial numbers are shown in bold blue text: iSR6200 login: guest Password: *************************
Summary of the content on the page No. 18
HW Version 31895-03 A SW Version 3.2.0.0rc6b2 Temp (Front/Rear/CPU1/CPU2) 35C/25C/31C/33C Power Cooling Module 2 ---------------------- Status Installed Power Source Not Connected Fan1/Fan2/Fan3 Healthy/Healthy/Healthy iSR6200 #> Using the GUI to Locate the Serial Number The following shows how to locate the serial number using the SANsurfer Router Manager utility provided by QLogic.
Summary of the content on the page No. 19
Finding the Serial Number on the Physical Blade The iSR6200 products have the serial number printed on the bottom of the blade. For a detailed procedure for removing the blade, refer to the iSR6200 QLogic intelligent Storage Router (iSR) Installation Guide, “Removal and Replacement” chapter. You can view the installation guide online at QLogic.com on the Downloads and Documentation page for your model number. Figure 15 shows the labeling on a QLogic iSR6200 Series blade. Figure 15. Locating
Summary of the content on the page No. 20
20
