Emerson Process Management BETTIS G01 user manual

User manual for the device Emerson Process Management BETTIS G01

Device: Emerson Process Management BETTIS G01
Category: Automobile Parts
Manufacturer: Emerson Process Management
Size: 0.22 MB
Added : 2/26/2013
Number of pages: 50
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Emerson Process Management BETTIS G01. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Emerson Process Management BETTIS G01.

For your convenience

If looking through the Emerson Process Management BETTIS G01 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Emerson Process Management BETTIS G01 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Emerson Process Management BETTIS G01 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Emerson Process Management BETTIS G01 User manual - Online PDF
Advertisement
« Page 1 of 50 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Emerson Process Management BETTIS G01 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Emerson Process Management BETTIS G01. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1

Instruction Manual
Form 5653
February 2007
Bettis Actuators G01 through G13
Bettis Service Instructions for Models G01
through G13 Pneumatic Actuators
The following instruction manual is for the Bettis of this manual. If you have any questions about
Actuator. This instruction manual was prepared by these instructions, contact the actuator manufacturer
Bettis, a member of the Valve Automation Division of before proceeding.
Emerson Process Management. Please contact
Bettis to ensure that the fol

Summary of the content on the page No. 2

Instruction Manual Form 5653 February 2007 Bettis Actuators G01 through G13 Fisher and Bettis are marks owned by the Emerson Process Management business division of Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners. The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accur

Summary of the content on the page No. 3

Summary of the content on the page No. 4

ENGLISH LANUAGE BETTIS SERVICE INSTRUCTIONS FOR MODELS G01 THROUGH G13 PNEUMATIC ACTUATORS PART NUMBER: 124840E REVISION: “B” DATE: 17 December 2001

Summary of the content on the page No. 5

Bettis P/N 124840E Revision “B” Page 1 of 46 CONTENTS SECTION 1.0 – INTRODUCTION PAGE 1.1 General Service Information ................................................................... 3 1.2 Definitions ............................................................................................... 4 1.3 General Safety Information ..................................................................... 4 1.4 Bettis Reference Materials ................................................................

Summary of the content on the page No. 6

Bettis P/N 124840E Revision “B” Page 2 of 46 CONTENTS SECTION 5.0 - MODULE REMOVAL AND INSTALLATION 5.1 Spring Module Removal .......................................................................... 31 5.2 Spring Module Installation ....................................................................... 33 5.3 Pneumatic Power Module Removal ........................................................ 37 5.4 Pneumatic Power Module Installation ..................................................... 3

Summary of the content on the page No. 7

Bettis P/N 124840E Revision “B” Page 3 of 46 SECTION 1 - INTRODUCTION 1.1 GENERAL SERVICE INFORMATION 1.1.1 This service procedure is offered as a guide to enable general maintenance to be performed on Bettis G01XXX, G2XXX, G3XXX, G4XXX, G5XXX, G7XXX, G8XXX, G10XXX, G13XXX Double Acting and Spring Return Series Single Power Module Pneumatic Actuators. This procedure can also be used on Bettis GXX2XX Double Acting Series Twin Power Modules Pneumatic Actuators. 1.1.2 Normal recommended service in

Summary of the content on the page No. 8

Bettis P/N 124840E Revision “B” Page 4 of 46 1.2 DEFINITIONS WARNING: If not observed, user incurs a high risk of severe damage to actuator and/or fatal injury to personnel. CAUTION: If not observed, user may incur damage to actuator and/or injury to personnel. NOTE: Advisory and information comments provided to assist maintenance personnel to carry out maintenance procedures. ES: Extended stop screw (for travel stop adjustment over a full 100° degree travel range). ES is not intended for use a

Summary of the content on the page No. 9

Bettis P/N 124840E Revision “B” Page 5 of 46 ACTUATOR BETTIS PART ACTUATOR BETTIS PART MODEL NUMBER MODEL NUMBER G01 None required G5/G7 117369 G2 123616 G8/G10 117368 G3/G4 117370 G13 122849 1.5.3 Commercial leak testing solution. 1.5.4 Non-hardening thread sealant. 1.6 LUBRICATION REQUIREMENTS NOTE: Lubricants, other than listed in step 1.6.1 should not be used without prior written approval of Bettis Product Engineering. 1.6.1. All temperature services (-50°F to +350°F)/(-45.5°C to 176.6°C) u

Summary of the content on the page No. 10

Bettis P/N 124840E Revision “B” Page 6 of 46 2.1.3 The Pneumatic Power Module can be disassembled while still attached to the Drive Module or the Pneumatic Power Module can be removed from the Drive Module and disassembled separate to the actuator (refer to Section 5 - Module Removal And Installation). 2.1.4 To ensure correct re-assembly; that is, with Pneumatic Power Module or Spring Module on same end of Drive Module as was, mark or tag right (or left) and mark mating surfaces. 2.1.5 For Sprin

Summary of the content on the page No. 11

Bettis P/N 124840E Revision “B” Page 7 of 46 2.2.4.2.2 Refer to assembly drawing page 2 of 2 Detail "E". If not already removed unscrew and remove two socket cap screws (3-130), with lockwasher (3-140), from outer end cap (3-80). 2.2.4.2.3 Remove socket cap screw (3-130) with lockwasher (3-140) from keeper (3-360). 2.2.4.2.4 Remove keeper (3-360) from outer end cap (3-80). 2.2.4.2.5 Push jackscrew (3-290) back into the outer end cap far enough so that the jackscrew adapter (3-280) will not inter

Summary of the content on the page No. 12

Bettis P/N 124840E Revision “B” Page 8 of 46 2.2.8.1.2 Remove o-ring seals (4-80) from the inboard end of tie bars (3-20). 2.2.8.2.3 Remove tie bars (3-20) by pulling the tie bars out and through piston (3-30). NOTE: G4 models have flats on outboard end of tie bars (3-20) for wrench placement. NOTE: G5 through G13 models have a female square on the out board end of tie bars (3-20) for wrench placement. 2.2.8.2 Remove G4 through G13 tie bars (3-20) as follows: Unscrew and remove tie bars (3-20) f

Summary of the content on the page No. 13

Bettis P/N 124840E Revision “B” Page 9 of 46 2.2.14 Unscrew and remove piston rod (3-40) from drive module. 2.3 DRIVE MODULE DISASSEMBLY NOTE: Review Section 2 steps 2.1.1 through 2.1.5 General Disassembly before proceeding with Drive Module Disassembly. 2.3.1 If not already removed remove piston rod (3-40) from drive module. NOTE: If the actuator is equipped with submerged stop screws with stop screw covers (1-195) then proceed to and complete steps 2.3.2.1 and 2.3.2.2 prior to doing step 2.3.2

Summary of the content on the page No. 14

Bettis P/N 124840E Revision “B” Page 10 of 46 2.3.12 Using hex cap screws (1-110), install into holes vacated by hex cap screws (1-120). Use these hex cap screws to jack the housing cover up for removal. Alternately rotate the hex cap screws clockwise until housing cover (1-20) is clear of housing (1-10). NOTE: G01, G2, G3 and G4 model housing cover will have cast tabs for placing prying tools to aid in cover removal. 2.3.13 Remove housing cover (1-20) from housing (1-10). NOTE: Groove pins (1

Summary of the content on the page No. 15

Bettis P/N 124840E Revision “B” Page 11 of 46 NOTE: One spherical washer (1-40) will be removed from guide block (1-30) when extension rod assembly is removed. On spring return actuators also one spherical washer (9-40) will be removed from guide block (1-30). 2.3.25 Remove the remaining spherical washer (1-40) from guide block (1-30). On spring return actuators also remove the remaining spherical washer (9-40) from guide block (1-30). 2.3.26 Unscrew and remove two stop screw nuts (1-190) from

Summary of the content on the page No. 16

Bettis P/N 124840E Revision “B” Page 12 of 46 2.6 M3 JACKSCREW DISSASSEMBLY NOTE: The jackscrew bearing retainer (7-110) / (5-110), needle bearing thrust washer assembly (7-100) / (5-100) or retainer ring (7-90) / (5-90) does not require disassembly from the jackscrew assembly (7-40) / (5-50) except for the need to replace worn parts. For disassembly of these items refer to step 2.6.7. Remove M3 handwheel or M3 hex drive hub per Section 2.5. 2.6.1 G01-M3 JACKSCREW DISASEMBLY FROM BLIND END CAP

Summary of the content on the page No. 17

Bettis P/N 124840E Revision “B” Page 13 of 46 2.6.4.2 Unscrew and remove hex flat nut (7-50) from M3 jackscrew assembly (7-40). 2.6.4.3 Unscrew and remove two socket cap screws (7-120) from M3 adapter (7-40). 2.6.4.4 Remove M3 jackscrew (7-40) from M3-SR adapter plate (7-10). 2.6.5 M3 THRUST BEARING DISASEMBLY FROM M3 JACKSCREW ASSEMBLY 2.6.5.1 Remove M3 bearing retainer (5-110) / (7-110) from inboard end of M3 jackscrew assembly (5-50) / (7-40). 2.6.5.2 Remove needle roller thrust bearing (5-10

Summary of the content on the page No. 18

Bettis P/N 124840E Revision “B” Page 14 of 46 NOTE: The parts and seals used in the actuator will be assembled using lubricant as identified in section 1 step 1.6.1. 3.1.5 For Spring Module Installation refer to Section 5 step 5.2. 3.2 DRIVE MODULE REASSEMBLY NOTE: Review section 3.1 General Reassembly before proceeding with Drive Module Reassembly. NOTE: Refer to assembly drawing page 2 of 2 Detail "B" for section drawing of guide block. 3.2.1 If guide bar bearing (2-20) is being replaced inst

Summary of the content on the page No. 19

Bettis P/N 124840E Revision “B” Page 15 of 46 3.2.10 Install second spherical washer (9-40) over threaded end of extension rod assembly (9-50). NOTE: The spherical side of the washer will go on the extension rod assembly facing the head of the extension rod assembly. 3.2.11 Install extension rod assembly (9-50) into guide block (1-30) and up against the first spherical washer (9-40). 3.2.12 Install extension retainer nut (9-60) over extension rod assembly (9-50) and screw into guide block (1-3

Summary of the content on the page No. 20

Bettis P/N 124840E Revision “B” Page 16 of 46 3.2.22 Align hole in guide block (1-30) with the matching holes in the two yoke/guide block bushings (2-30) and the slots in the arms of yoke (1-70). NOTE: The yoke pin can be held in place by installing a screw into the .375-16UNC tapped hole in the upper end of yoke pin (1-80). 3.2.23 Install yoke pin (1-80) by inserting into the upper yoke arm, upper yoke/guide block bushing, guide block, lower yoke/guide block bushing, lower yoke arm and resting


Alternative user manuals
# User manual Category Download
1 Emerson Process Management 3024C User manual Automobile Parts 2
2 Emerson Process Management 1052 User manual Automobile Parts 1
3 Emerson Process Management BETTIS G13 User manual Automobile Parts 3
4 Emerson Process Management FISHER 657 User manual Automobile Parts 5
5 Emerson Process Management ControlWave EFM 4710A User manual Automobile Parts 1
6 Emerson Process Management 667 User manual Automobile Parts 0
7 Emerson Process Management ControlWave EFM FGR09CSU User manual Automobile Parts 2
8 Emerson Process Management ControlWave EFM 3808 User manual Automobile Parts 8
9 Emerson Process Management El-O-Matic E and P Series P2500 User manual Automobile Parts 27
10 Emerson Process Management El-O-Matic E and P Series E25-E950 User manual Automobile Parts 1
11 Emerson Process Management El-O-Matic E and P Series P4000 User manual Automobile Parts 19
12 Emerson Process Management 1051 User manual Automobile Parts 0
13 Sony BP-GL95 User manual Automobile Parts 25
14 Sony BP-GL65 User manual Automobile Parts 2
15 Philips Epic 50PF9966 User manual Automobile Parts 3
16 Philips HTS3011 User manual Automobile Parts 2
17 Philips SDJ6040W User manual Automobile Parts 1