Summary of the content on the page No. 1
Accessory Application Publications No.
All 21624
2001 ACCORD
INSTALLATION
SECURITY SYSTEM
2- AND 4-DOOR
Issue Date
(INCLUDES V6)
INSTRUCTIONS
AUG 2000
PARTS LIST Security System Attachment (sold separately):
P/N 08E55-S84-100
Security System (sold separately):
P/N 08E51-S84-100 Security system
wire harness
2 Remote controls
Control unit
Sub-harness
LED
White connector clip
Push nut
Control unit bracket
2-Pin connector (for LED)
2 Relay brackets
Disarm switch
5 Short wire ties
Window decal
3-Pin
Summary of the content on the page No. 2
Wire tie with clip TOOLS AND SUPPLIES REQUIRED Small flat-tip screwdriver #2 Phillips screwdriver Eye protection (face shield, safety goggles, etc.) Center punch Drill 9 Long wire ties 5.5 mm, 10 mm, and 12 mm Drill bits Tape measure File Felt-tip pen Pliers Cushion tape 17 mm Combination wrench 10 mm Socket Ratchet Scissors Red connector clip Utility knife Illustration of the Security System Installed on the Vehicle Relay, 4-pin 5-PIN 4-PIN LEFT RELAY RELAY FUSE BOX LED RIGHT FUSE BOX Relay, 5-
Summary of the content on the page No. 3
Adjusting the Control Unit INSTALLATION Use a small flat-tip screwdriver to change the Customer Information: The information in this mode switch and the horn/siren switch and to installation instruction is intended for use only by adjust sensitivity. skilled technicians who have the proper tools, equipment, and training to correctly and safely add GLASS BREAKAGE MODE SWITCH equipment to your car. These procedures should not SENSOR be attempted by "do-it-yourselfers." 1. Make sure you have the
Summary of the content on the page No. 4
5. Remove the left fuse box cover (three retaining 7. Remove the driver’s door sill molding (four clips). clips and two tabs). CLIP TAB CLIP DRIVER'S DOOR SILL MOLDING LEFT FUSE LEFT FUSE BOX COVER BOX TAB CLIP RETAINING CLIPS 6. Remove the driver's dashboard lower cover (three 8. Remove the kick panel (two clips, and pull). screws, and five retaining clips). SCREW KICK PANEL SCREW SCREW DRIVER'S DASHBOARD CLIP LOWER COVER CLIP 4 of 12 All 21624 (0008) © 2000 American Honda Motor Co., Inc - All
Summary of the content on the page No. 5
9. Remove the right fuse box cover (three retaining 11. Open the glove box, and remove the two screw clips and two tabs). caps and seven self-tapping screws. Unplug the connector, and remove the glove box by pulling it toward you. GLOVE BOX TAB CLIP CONNECTOR SELF-TAPPING SCREW CAPS RIGHT FUSE BOX COVER RIGHT FUSE BOX TAB 12. Lower the steering wheel tilt lever. Remove the upper and lower steering column covers (three 10. Remove the passenger’s dashboard lower cover screws, six tabs, and one har
Summary of the content on the page No. 6
13. Measure and mark the upper steering column 16. Locate the 2-pin connector included in the kit, and cover. lower the lock. Firmly push the LED terminals into the 2-pin connector. Insert. 5.5 mm DRILL Lock. UPPER STEERING COLUMN COVER WHITE WIRE 20 mm RED WIRE 17. Measure and mark the driver's dashboard lower MARK cover. (If necessary, remove the insulation.) 14. While wearing eye protection, lightly center-punch the mark; then drill a 5.5 mm hole through the upper steering column cover. Remov
Summary of the content on the page No. 7
19. Route the terminal ends of the disarm switch 21. Push the wire tie with clip into the hole in the back through the hole you just drilled, and secure it with of the control unit bracket. Position the control unit the washer and 12 mm nut from the kit. bracket on the driver's dashboard lower cover, and install the three self-tapping screws from the attachment kit. NUT SELF-TAPPING SCREW WASHER WIRE TIE DRIVER'S WITH CLIP DASHBOARD LOWER COVER CONTROL UNIT BRACKET DISARM SWITCH BACK OF DRIVER'S
Summary of the content on the page No. 8
23. Secure the disarm switch wire harness to the 26. Attach the 14-pin connector of the security system disarm switch with one short wire tie, then attach wire harness to the side of the vehicle connector. the harness to the driver's dashboard lower cover with two halves of a cushion tape in the areas LEFT FUSE BOX shown. (Cut a cushion tape in half with scissors, and use the two halves to secure the harness.) SECURITY SYSTEM WIRE HARNESS CONNECTOR DISARM SWITCH 14-PIN CONNECTOR CLIP SHORT WIRE
Summary of the content on the page No. 9
28. Remove the upper bolt that fastens the engine 31. Unplug the 20-pin connector from the left fuse box, hood opener, and attach the ground terminal of the and plug the two 20-pin connectors (white) of the security system wire harness with the ground bolt security system wire harness in between. from the kit. VEHICLE 20-PIN 1-PIN CONNECTOR OF CONNECTOR SECURITY SYSTEM WIRE HARNESS (WHITE) LEFT FUSE No. 5 BOX CONNECTOR OF FUSE BOX ENGINE HOOD OPENER 20-PIN CONNECTORS GROUND BOLT SECURITY SYSTEM
Summary of the content on the page No. 10
33. Remove the clip from the hole in the left knee 37. Position the 5-pin and 4-pin relays onto the other bolster, use a utility knife to cut the clip off of the relay bracket, and install one 6 x 12 mm vehicle harness. Take care not to damage the washer-bolt and 6 mm nut. vehicle harness. RELAY BRACKET LEFT KNEE 6 mm BOLSTER FLANGE 6 x 12 mm NUT WASHER-BOLT 4-PIN RELAY About 45° VEHICLE HARNESS 5-PIN RELAY HARNESS CLIP (Cut and discard.) 34. Assemble three fuse cases as shown. Attach the 5-PIN
Summary of the content on the page No. 11
39. Route the 2-pin connector of the LED through the 41. On the left of the steering wheel, secure the lower steering column cover, and connect it to the security system wire harness to the vehicle 2-pin connector of the security system wire harness with three long wire ties in the areas harness. Reinstall the lower and upper steering shown. column covers. LONG WIRE TIES UPPER STEERING COLUMN LED COVER LED HARNESS LEFT FUSE BOX LOWER STEERING COLUMN VEHICLE COVER HARNESS SECURITY SYSTEM 2-PIN WI
Summary of the content on the page No. 12
43. Plug the 3-pin connector of the security system 46. Route the sub-harness along the vehicle harness. wire harness into the 3-pin connector of the disarm Inside the glove box, locate the 2-pin connector switch harness. Plug the 22-pin connector of the blue-taped to the vehicle harness, and remove the security system wire harness into the control unit; blue tape to free the connector. Plug the 2-pin then reinstall the driver's dashboard lower cover. connector of the sub-harness into the 2-pin
